The LED Based Solar Lantern is
a portable lighting device suitable for either indoor or
outdoor lighting covering a full range of 360 degrees. In
consists of a lamp, battery and electronics, all placed in a
plastic housing and a SPV module.
LED Based Solar Lantern is a device that operates by solar
energy, which is converted to electrical energy by the SPV
module and stored in battery. Red & Green LEDs are provided on
the housing of lantern for indicating battery discharge &
battery charging respectively.
The LED Based Solar Lantern can be used to provide sufficient
light in the homes where electricity is irregular and scarce.
It is powered through a Solar Photovoltaic Module (SPV). These
modules are manufactured to comply with stringent quality
standards and are capable of withstanding the toughest
environment conditions over a long service life.
- Latest Technology
- Easy Installation and
- Long Life Span
- Energy Efficient
- It can be used in indoor as
well as outdoor
white Nichia LEDs
||< 2.5 W
Depending on what the customer has ordered, ensure the
following items have been delivered:
Lantern : 01 No.
SPV Module : 01 No.
Accessories : 01 Set
Lantern from the carton, Carefully go through the Installation
& Maintenance Guide. Inspect for signs of any damage. If any
damages are observed, notify the dealer name and return the
unit to the factory immediately. If there are no obvious signs
of damage, read safety instructions and proceed with
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use the Solar Lantern
near water and avoid contact of lantern with rain, snow, or
liquids of any type.
- Clean only with dry cloth.
- Install in accordance with
the instructions given below.
- Do not install near any heat
sources such as radiators, stoves or other equipment that
- CAUTION: Use only
maintenance free battery.
- Do not open lantern
yourself. Take it to an authorized service center, when
service or repair is needed.
Fix the SPV
module to the mounting stand with inclination angle to the
sunlight in a suitable location, which must be in contact
with direct sunlight and away from trees and other types of
cable properly from SPV module to Lantern up to where the
lantern has to be charged and insert the cable jack to the
ďSPV INĒ provided on lantern housing.
Check for the
fuse and put properly in the holder provided on the lantern
green LED glowing as and when the cable is inserted during
daytime when sunlight is available.
Solar Lantern must be charged for 2 sunny days for best
System is ready for operation.
To check the
Lamp Operation, remove the SPV input and switch ON the
Lantern light. Observe the light output and restore the SPV
input and lantern switch.
Dos and Doníts
solar Panel clean from Dust and Bird droppings.
||Do not hammer
while fixing the SPV Module connections.
|Keep the Lamp
cover clean to get maximum light out put.
||Do not keep
Lantern near flame and water.
connections should be firmly tightened at SPV module.
in reverse polarities while replacing battery.
Clean the solar
panel regularly with a damp towel to ensure optimal
performance of the SPV Module. Donít use any type of solvent
for cleaning and be careful not to put too much pressure on
the panel during the cleaning process. To extend the life of
your Home Lighting System, it is recommended that solar panel
is stored indoors during the winter months or any other
extreme weather conditions.
Keep the SPV
Module free of Dust and Bird dropping etc, by wiping it with
clean damp/dry cloth.
Keep the Lamp
cover clean to get maximum light out put.
Light not switching ON:
2. Battery not charging
(Green LED not glowing):
- Check for loose contact in
the SPV module to Lantern cable.
- Check the SPV Module output
voltage. If it is not sufficient check any shadows /
physical obstructions, which are blocking sunlight falling
on the SPV Module. If still problem exists replace the SPV
3. Battery discharging
Replace the battery as
the SPV Module.
carefully by unscrewing three screws of the bottom of the
battery clamp and disconnect the battery by removing lugs.
remove the Battery from the Lantern.
Place the new
Battery in the Lantern, and observe the polarity while
reconnecting the terminals. (Red for +VE and Black for ĖVE).
If none of
them works call nearest service center/factory.
any solar product for an extended period of time, be sure to
remove the batteries.
solar product without regular recharge or removal could
cause permanent damage to the rechargeable batteries